Four Quick Fixes for Plumbing You Should Know

There are times when you just can’t wait for a plumber to come fix a minor plumbing issue. Since waiting could cause water damage, it’s best to be prepared with a few quick fixes to help you out until the plumber arrives.
SWR Plumbing has a team of professional plumbers with years of experience who are ready to offer you quick, dependable, and affordable plumbing services. Don’t hesitate to call us the next time you need a plumber because we are available around the clock.
If you know what you’re doing, problems like clogged drains and leaking pipes are typically simple to fix. Fortunately, common issues can be resolved quickly with home remedies. You can save money and avoid significant water damage to your home with these fixes. Here are four examples.

Faulty Water Heater

Immediately turn off your water heater if it is leaking. You can then try to solve the issue yourself or call a professional to fix it. You can test the pressure relief valve to see if it is functioning properly if you are comfortable doing so. The accumulation of sediment is the primary cause of the inefficiency of the majority of water heaters. The water heater cannot properly heat the water when a layer of sediment settles at the bottom of the tank. Your water heater will have to work harder to heat the water as a result, which may cause hot water to arrive slowly.

How to Flush Your Water Heater

If you suspect that sediment is the problem, you can flush the tank. Turn off your water heater to accomplish this. After that, give one of your sinks hot water for about ten minutes. Attach a garden hose to the drain valve and turn off the cold water valve that connects to your water heater. Connect the hose to a floor drain in the vicinity. Reopen the cold water valve without closing it or disconnecting the garden hose. After allowing the water to run until it is clear, close the drain valve. Restart your water heater to see if the issue has been resolved.

Leaking Pipes

One of the most prevalent issues with plumbing is leaking pipes. The good news is that they are frequently simple to repair. The first step is to identify the source of the leak. After that, turn off the water to the affected area and measure the leaking pipe’s circumference.

How to Turn Off the Water

To shut off the water to the leaking pipe, locate the shut-off valve that is closest to you. The shutoff valve for showers and tubs is usually on the wall. You can turn a small knob to the right under sinks and toilets to turn off the water. To turn off the water, find the shutoff valve and turn it clockwise.
However, you will need to shut off your home’s main water supply if the leak is far from a local shutoff valve. Typically, the location of the main shutoff valve is where the city water supply enters your home. To turn it off, turn the handle clockwise once you’ve located it.

The Accurate Repair Supplies

To stop the leak until you can replace the leaking pipe, you should go to the closest hardware store to purchase the accurate repair supplies. Purchase an epoxy compound for iron pipes. If you have PVC, copper, or any other kind of pipes, get a wrap or clamp for them.

Fixing a Leaking Iron Pipe: Place the epoxy putty where the pipe is leaking on the outside. By applying it all the way around the pipe, you can get a good seal.

How to Repair Leaking Copper, PVC, and Other Pipes:

To fix this kind of leak, you can use a wrap or a pipe clamp. Sandpaper can be used to clean the area around the leak first. The next step is to wrap or clamp the pipe all the way around. In order for it to seal, make sure it is tight. The pressure will seal the leak until the pipe can be replaced.
Despite the fact that these products will stop water from leaking, they are not long-term solutions. To prevent further damage to your house, you will need to replace the pipe as soon as possible.

Leaking Pipe Joint

Compared to leaking pipe joints, repairing leaking pipes is simpler. The pipe joint’s angle can make it hard to get a good seal. The good news is that these kinds of issues can be handled with some tools.
Flexible rubber repair sleeves and connectors for pipes can be used on pipes that are angled. They will form a tight seal by pressing against the pipe’s sides. The majority of hardware stores carry these tools.

How to Replace a Cracked Pipe Joint: When using rubber pipe connectors or repair sleeves, it’s critical to get the measurements right. The rubber connectors should be cut and placed tightly over the leaking pipe joint. In order for it to seal, make sure it is tight. The pressure will seal the leak until the pipes can be replaced. Smaller joint leaks are better handled by repair sleeves. The rubber wrap should be clamped in place.
Again, these are not permanent solutions, and in order to prevent further harm to your house, you will need to replace the pipe as soon as possible. Duct tape can be used to repair sleeves or support the rubber pipes if the leak persists. However, because of this, it would be even more crucial to replace the pipe as soon as possible.

Broken or Cracked Porcelain

Sinks made of porcelain are a common issue in both old and new homes. Although it may not appear to be a significant issue, neglecting it can actually result in serious issues. Mold and mildew growth can result from water seeping into the surrounding area if your sink has a crack. Additionally, cracks may expand over time, necessitating the purchase of a new sink in the end.
Fortunately, cracks in your porcelain sink can be easily fixed. Super glue can be used to fill in small cracks. Apply the glue to the crack and let it dry. The crack will be sealed with this, preventing water from entering.
You will need to use plumber’s putty for larger cracks. Apply plumber’s putty to the inside of the leak first. Use a putty knife to evenly distribute the putty after you squeeze it into the crack. After that, apply caulk to the top to make a second seal. Although it is more difficult to apply on its own, the caulk lasts longer than the putty. Before using the sink, allow the putty and caulk to completely dry.
In the short term, these solutions will work, but if the sink is severely cracked or broken, it should be replaced. Over time, cracks can develop, eventually resulting in leaks. Preventing water damage to your home only necessitates a new sink.
It’s always best to hire a professional if you don’t feel confident performing any of these quick fixes on your own. They can assist you in avoiding problems in the future and have the expertise and experience necessary to effectively resolve your plumbing issue.
SWR Plumbing is available to assist you with all of your plumbing emergencies. We offer a wide range of services, including drain cleaning, quick fixes, and pipe repair and replacement. To set up a consultation, call 1800 255 372 right now. We are always willing to assist!